Ring & pinion ratio.
06-25-2014, 05:42 AM (This post was last modified: 06-25-2014 05:43 AM by izanagi.)
Post: #18
Re: RE: Ring & pinion ratio.
(06-25-2014 12:03 AM)jondee86 Wrote:  
(06-24-2014 08:53 AM)izanagi Wrote:  [quote='jondee86' pid='162334' dateline='1403567791']
What do you mean by that:
If the gears appear to be
in good condition, you could try adjusting the contact patch, or just put
up with the noise, and hope that it settles after a while. ?????

I should set up the ring much closer of the pinion ?
With the same method showed in the factory service manual ?

When you dismantled the diff there should have been a wear pattern
(contact patch) visible on the crownwheel teeth. Providing the contact
patch was correctly placed on the face of the tooth, you should have
tried to put the diff back together with the contact patch in the same
position. The procedure is in the FSM, and some nice pictures here...

[Image: AEU86 AE86 - Re: RE: Ring & pinion ratio.]
http://www.pirate4x4.com/tech/billavista...ear_Setup/ Scroll to the bottom of the page.

Did you adjust the contact patch during final assembly of the diff ?

Cheers... jondee86

Yes i did with gear marking compound

Envoyé depuis mon GT-I9100 avec Tapatalk
Find all posts by this user


Messages In This Thread
Ring & pinion ratio. - izanagi - 06-23-2014, 01:32 PM
Re: RE: Ring & pinion ratio. - Bean - 06-23-2014, 03:14 PM
Re: Ring & pinion ratio. - izanagi - 06-23-2014, 03:43 PM
RE: Ring & pinion ratio. - jondee86 - 06-24-2014, 01:56 AM
RE: Ring & pinion ratio. - Project D - 06-23-2014, 05:43 PM
RE: Ring & pinion ratio. - driftmaniacae86 - 06-23-2014, 10:11 PM
Re: RE: Ring & pinion ratio. - izanagi - 06-23-2014, 11:48 PM
Re: RE: Ring & pinion ratio. - izanagi - 06-24-2014, 08:53 AM
RE: Ring & pinion ratio. - jondee86 - 06-25-2014, 12:03 AM
RE: Ring & pinion ratio. - Uzelac - 06-24-2014, 01:16 PM
RE: Ring & pinion ratio. - AJPS - 06-24-2014, 06:50 PM
RE: Ring & pinion ratio. - Uzelac - 06-25-2014, 06:19 PM
Re: RE: Ring & pinion ratio. - Bean - 06-24-2014, 08:29 PM
RE: Ring & pinion ratio. - izanagi - 06-24-2014, 08:31 PM
Re: RE: Ring & pinion ratio. - Bean - 06-24-2014, 10:20 PM
RE: Ring & pinion ratio. - izanagi - 06-24-2014, 10:43 PM
Re: RE: Ring & pinion ratio. - Bean - 06-24-2014, 10:58 PM
RE: Ring & pinion ratio. - izanagi - 06-24-2014, 11:10 PM
Re: RE: Ring & pinion ratio. - izanagi - 06-25-2014 05:42 AM
RE: Ring & pinion ratio. - AJPS - 06-25-2014, 11:53 AM
RE: Ring & pinion ratio. - Bean - 06-25-2014, 05:20 PM
Re: RE: Ring & pinion ratio. - izanagi - 06-25-2014, 04:09 PM
RE: Ring & pinion ratio. - izanagi - 06-25-2014, 09:52 PM
RE: Ring & pinion ratio. - izanagi - 06-29-2014, 09:08 PM
Re: RE: Ring & pinion ratio. - Bean - 06-29-2014, 10:19 PM
RE: Ring & pinion ratio. - izanagi - 06-29-2014, 10:44 PM
RE: Ring & pinion ratio. - jondee86 - 06-29-2014, 11:41 PM
RE: Ring & pinion ratio. - assassin10000 - 07-05-2014, 07:35 PM

Possibly Related Threads...
Thread Author Replies Views Last Post
  ring gear bolts DJexor 3 5,388 12-26-2016 10:56 PM
Last Post: totta Crolla
  DIY: a quick outline on why & how to set pinion angle. assassin10000 9 18,242 12-21-2016 10:28 PM
Last Post: ditn
  Checking ring gear diff izanagi 3 4,971 07-09-2014 07:38 AM
Last Post: jondee86
  axle swap time how capable is a std crownwheel and pinion fax0815 32 45,880 09-26-2013 08:33 PM
Last Post: Lajoosh
  Gear end , drive pinion height filh 5 11,116 06-27-2013 12:29 AM
Last Post: filh

Forum Jump:


User(s) browsing this thread: 14 Guest(s)

Contact Us | AEU86 | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication