the many more 4AGZE questions topic

[ditn]

<=been in the hospital, so couldnt respond.
looks nice

Didnt recieve any response from dp engineering so i will search someone else or wait for now.

I found an exhaust system from janspeed but the sice is 58 mm or 2.3 inch,would this also be ok?

[ditn]

another questions
4-2-1 or 4-1 for a 4AGZE?

[Project D]

ditn Wrote:another questions
4-2-1 or 4-1 for a 4AGZE?

It depends how you would like your car behave.

If you like to drive only on the low / middle rev and have all the torque / hp there, go for a 4-2-1. (it would be my personnal choice for a gze)

If you want to keep some hp at a higher rev (flattening your curve somehow) go for a 4-1.

But I don't think it will change things a lot, after all the supercharger is prone to override all the other components.

[NoHachi]

Its not always as simple as that though. If you have a choice between a perfect 4-1 and a perfect 4-2-1 then yes.

But I've seen only 1 4AGE header that comes close.

The quality of the welding, the merges used, the use of correct diameters and lengths of parts, they all make a difference.
A good 4-2-1 will outperform a normal 4-1 by a large margin in top end power.

[ditn]

i have a janspeed 4-1 header for the moment.
So would you say i better go for a 4-2-1 or just stick with what i have.

I saw this header online somewhere its a 4-2-1 from a 4GZE

[oldeskewltoy]

ditn Wrote:i have a janspeed 4-1 header for the moment.
So would you say i better go for a 4-2-1 or just stick with what i have.

I saw this header online somewhere its a 4-2-1 from a 4GZE

That header APPEARS to be a HKS for LHD


It should be decent for boost, check... I believe the OD of those primaries are 42mm

[ditn]

its gone already,guess i will keep my 4-1 for now then and save up for a good 4-2-1 like you say.

gonna buy a 58mm/2,3 inch janspeed system i think,is the closest i can find thats still affordable.
Is there a LHD and RHD janspeed system or is it all the same,dont want to end up with a RHD while my car is LHD

[Vaptor]

Have you looked at this one?

http://www.ebay.com/itm/181004077932?ssP...1497.l2648

I have bought this one, and its a good build quality, pipes are bend smooth and are equal length. and cheap to

[Gtsi-R]

ditn Wrote:<=been in the hospital, so couldnt respond.
looks nice

Didnt recieve any response from dp engineering so i will search someone else or wait for now.

I found an exhaust system from janspeed but the sice is 58 mm or 2.3 inch,would this also be ok?

do you still need awenser from DP engineering?
I know them personally, worked togheter with Pieter few years ago
I could drive by sometimes.. only 15km away from my home..

Vaptor Wrote:Have you looked at this one?

http://www.ebay.com/itm/181004077932?ssP...1497.l2648

I have bought this one, and its a good build quality, pipes are bend smooth and are equal length. and cheap to

I am personally not convinced about the quallity? is it OK yes? basic looks OK, but i am not sure if it will last long

regards, Roel

[ditn]

nah
i dont think i want an answer from them anymore

hm im not to keen about the brand but i will keep it in mind thanks.