20v itb inlet manifolds

Threaded Mode | Linear Mode

20v itb inlet manifolds

12-10-2012, 07:12 PM

Post: #13

Bean

AEU86 oldtimer

Posts: 2,579
Joined: Jul 2006
Reputation: 1

ZDoman Wrote:ae86-92 tps's are only differ in the connector,
ae101 and 111 tps's works with the same resistance etc but it has the wires "upside down" so for example when you want to use the ae111 tps with an ae86 ECU you should change the wires direction with 180 degrees.

you should be good then, as long as the resistance is the same. Just use the smallport TPS and wire it correctly to the freedom ECU to match the schematics of the Freedom ECU and TPS.
At the end of the day the TPS is just a potentiometer, so if your not sure which wire does what use a multimeter and measure resistance while moving the throttle.

AE86 ex-daily

« Next Oldest | Next Newest »

Messages In This Thread

20v itb inlet manifolds - totta Crolla - 12-10-2012, 11:58 AM

[] - Bean - 12-10-2012, 12:04 PM

[] - totta Crolla - 12-10-2012, 12:19 PM

[] - Bean - 12-10-2012, 12:58 PM

[] - Bean - 12-10-2012, 01:06 PM

[] - totta Crolla - 12-10-2012, 03:18 PM

[] - Bean - 12-10-2012, 03:29 PM

[] - totta Crolla - 12-10-2012, 03:46 PM

[] - Bean - 12-10-2012, 04:20 PM

[] - totta Crolla - 12-10-2012, 05:04 PM

[] - Bean - 12-10-2012, 05:39 PM

[] - ZDoman - 12-10-2012, 06:51 PM

[] - Bean - 12-10-2012 07:12 PM

[] - totta Crolla - 12-11-2012, 12:17 AM

[] - Bean - 12-11-2012, 10:05 AM

[] - totta Crolla - 12-11-2012, 04:18 PM

[] - Bean - 12-11-2012, 05:49 PM

[] - oldeskewltoy - 12-11-2012, 07:46 PM

[] - Bean - 12-12-2012, 12:41 AM

[] - Project D - 12-12-2012, 01:49 AM

[] - Bean - 12-12-2012, 09:20 PM

[] - Project D - 12-12-2012, 09:31 PM

[] - totta Crolla - 12-14-2012, 11:58 AM

[] - Bean - 12-14-2012, 12:21 PM

Possibly Related Threads...
Thread		Author	Replies	Views	Last Post
	Smallport inlet manifold	totta Crolla	6	3,459	01-17-2022 05:14 PM Last Post: oldeskewltoy
	4A-GE 20V ITB bolt patterns	kjb	7	12,114	02-27-2016 01:23 PM Last Post: kjb
	How to install 20V ITB on 16V head	Mr.komp	7	11,827	12-28-2015 05:35 PM Last Post: pack
	Machining Pistons to run 20v head... And FCR's on a 20v?	PazzaAE86	2	5,136	09-15-2013 01:08 AM Last Post: jondee86
	4AGE 20v ITB vacuum instructions on Intecracing.com	JAVResistance	17	34,142	05-07-2011 05:50 AM Last Post: jondee86

User(s) browsing this thread: 7 Guest(s)